Tectite fitting for tight space

Bogart

Need to use a couple of 28mm tectite fitting, space very limited so soldering is out. Looking on the Peglar site there seems so many that look the same. Some they state as slip fittings, how do they work on a grab ring fitting?

scott_d

Tectite 28mm equal coupler

Tectite Sprint Copper Push-Fit Equal Coupler 28mm

Order online at Screwfix.com. Simple, push-fit installation with a tamperproof, slim-line fitting. Guaranteed electrical continuity on copper pipe and high performance 114°C at 10bar. FREE next day delivery available, free collection in 5 minutes.

www.screwfix.com

Gasmk1

Tectite are a bit like shark grip they are non removable (I think) I have used them a couple of times in similar situation to yours if you look at them it's an o'ring then some sort of stainless tooth grip ring

Bogart

The sprint ones are non-demountable, but an advantage, in my case, is they are the shortest in length as I have not much leeway for pipe movement. This is why I asked about the slip fitting not sure how that works using grab rings.

snowhead

There's a video here, it's from the U.S.A so is 3/4" but shows the principle.
Basicaly the fitting is extended on one side to allow the pipe to push in allowing the other end room to fit.
Then using the release tool it slides into position;

View: https://www.youtube.com/watch?v=gjtMTmHlOnE

Bogart

Right am with it now. Was unsure how it slipped as there is a grab ring either end, was not aware one used the demounting tool. Quite obvious when one sees it done.
One comment on the guy's video was I thought the copper pipe was rather marked and scored. Does not matter with a soldered fitting but I have found that one needs a nice smooth pipe to effectively seal the O ring.
Thanks for taking time to reply guys.

snowhead

I think he was concentrating on videoing as opposed to not scoring the pipe.
I would think if you had the release tool in both hands the claws would lift off.

Diffferent video, still USA, jump to 2.40 ish;

View: https://www.youtube.com/watch?v=u_NINyKcWDM

Bogart

I think the demount tool looks good here no need to be pushing into the fitting at the same time as pushing the fitting home.

Bogart

It is interesting in both videos that they are using T fittings, it gets a bit more awkward if like me a straight coupling is required. The T offers a much longer body to slide onto the pipe. Have just spoken to Pegler who say on a straight slip fitting, 45144 you gain about 10mm of leeway, over the non slip 45123, ie you can slip it 10mm into the other end before it will foul the grab ring. In my case I do not need it dismounting and the Sprint fitting 75503 gives me the same leeway, no 10mm slip but the body is 20mm shorter divided by 2 giving me 10mm. Only problem with Sprint is not demountable.

Stigster

Bogart said:
One comment on the guy's video was I thought the copper pipe was rather marked and scored. Does not matter with a soldered fitting but I have found that one needs a nice smooth pipe to effectively seal the O ring.

I think there's two parts to this. Firstly I believe that the bright light the guy is using to film with is making the scratches look a great deal worse than they really are. Also, in my experience if a scratch on a copper pipe does not easily catch a fingernail drawn across it, it will seal and test fine with this design of fitting. The o-ring is malleable enough to seal against such marks.

If the pipe is visibly marked and easy to change, change it for a nicer piece. Where that is not feasible, if your fingernail easily skips over the scratch there's every chance it'll be fine. Obviously use experience and common sense but a marked or lightly scratched pipe can be joined onto if you really have to.

Beware the manufacturer's instructions though. If it causes damage I'd be worried they could say you didn't fit it to clean pipe so it's your fault. Obviously use your common sense depending upon the location. I think most of us have been amazed at how a fitting with an o-ring has sealed on a chewed up piece of alkathene on a temporary site supply.

In a hidden position, err on the side of caution and do everything you can to be connecting to clean perfectly smooth pipe though.

Bogart

Have a couple of the slip fittings on order. Think I considered most possibilities with this, even slip copper fittings.
Necver even knew you could get soldered slip fittings. Opted for the tectite as the joints will be vertical and to my mind using a copper slip fitting I need 3 hands!

Stigster

Bogart said:
Necver even knew you could get soldered slip fittings.

If I need a slip coupling for copper I usually make one out of an end feed fitting by using my pen knife to scrape away the stop inside. A small half-round file works too but takes a bit longer. Another option I have used is to cut a coupling length piece of copper tube and use my socket forming tool to open up the small piece of tube so it slips all the way on to a pipe.

You can also buy them ready made in both end-feed and integral solder ring.

Tectite fitting for tight space

Bogart

scott_d

Tectite Sprint Copper Push-Fit Equal Coupler 28mm

Gasmk1

Bogart

snowhead

Bogart

snowhead

Bogart

Bogart

Stigster

Bogart

Stigster

Similar threads

New Posts Threads Members

New Posts

New Threads

Members