PC120 Bucket Pivot Pin Fitment, Dimensions, and Replacement Guide

A PC120 bucket pivot pin must match the excavator’s linkage configuration, pin diameter, working length, and retention arrangement. “PC120” alone is not enough to confirm an exact fit: dimensions and configurations can vary by machine series, serial range, bucket, and linkage setup. Before ordering, compare the old pin and the machine’s parts information, then verify key measurements in millimetres. At Zhonghai Jiuchuan, we recommend confirming the application and dimensional drawing before requesting a quotation for a replacement bucket pin.

For more information, please visit our website.

Who This Guide Is For

This guide is for equipment parts distributors, repair workshops, fleet maintenance teams, and procurement professionals sourcing a PC120 bucket pivot pin. It is also useful when an existing pin is worn, damaged, missing, or difficult to identify by part number alone. The steps help you prepare accurate information for a supplier without treating a general model name as a guaranteed fitment reference. For a machine-specific decision, use the serial number and the applicable parts documentation whenever available.

How a Bucket Pivot Pin Fits the Linkage

A bucket pivot pin passes through aligned bores in components of the bucket and excavator linkage, forming a pivot point. It allows the connected parts to articulate as the hydraulic cylinders move the linkage. The pin works with the surrounding bushings, retainers, seals, and lubrication arrangement, so correct fitment depends on more than its outside diameter. A pin that is too short, too long, or incompatible with the retention method can create installation and operating problems.

Bucket pivot pins are not interchangeable with every other pin on an excavator. A machine may use separate pins at the bucket, link, arm, and cylinder connections, and those locations can have different dimensions and retention details. Identify the exact joint before measuring or ordering. If the original pin’s location is uncertain, compare the parts diagram or ask a qualified service professional to verify it.

Fitment and Dimension Overview

There is no single PC120 dimension that should be assumed to apply to every machine and bucket configuration. The pin’s nominal size should be confirmed against the relevant parts information or an unworn section of the original component. Measurements from a worn pin can be smaller than its original nominal diameter, while corrosion or deformation may make readings unreliable. Treat field measurements as identification and comparison data, not as a substitute for a confirmed specification.

Practical Measurement Method

Clean the pin before measuring, and remove loose rust, grease, and debris that could affect contact with the measuring tool. Use a micrometer or suitable precision measuring instrument for diameter checks; a tool with 0.01 mm resolution can help record small differences, but it does not make a worn or damaged surface a reliable nominal reference. Record diameter at three positions along the usable length and in two directions at each position. This six-reading check can help reveal taper, localized wear, or out-of-round conditions.

Measure overall length and working length separately, and photograph the pin beside a ruler or measuring scale for reference. Do not infer a missing shoulder, groove, or retainer feature from a single photograph. If the pin is broken or heavily worn, provide the supplier with the machine serial number, joint location, part number if known, and measurements from the mating components. Clear information reduces the risk of quoting a visually similar but incorrect part.

Materials and Design Details to Confirm

Pin material, heat treatment, surface condition, and manufacturing tolerances should be confirmed from the supplier’s product information or drawing rather than guessed from appearance. A buyer may encounter pins described as alloy steel or as having a hardened working surface, but those descriptions should be tied to the specific item being quoted. Ask which material and process apply to the proposed pin and whether documentation is available for the order. Do not assume that a particular treatment, hardness, or coating is included unless it is confirmed in writing.

Also check whether the replacement is supplied as a pin only or as part of a repair set. Depending on the joint and supplier offering, related items may include bushings, seals, or retaining hardware. Replacing a pin without checking the mating components may leave excessive clearance or recurring movement if those components are also worn. Confirm the scope of supply before comparing quotations.

Goto Zhonghai Jiuchuan to know more.

Selection Framework Before You Order

Step 1: Identify the Machine and Joint

Record the complete machine model designation, serial number, and the exact bucket linkage position. Include the bucket or attachment identification if it has been changed from the original configuration. Use a parts diagram or service information to cross-check the joint and any available part number. If the machine has been modified, tell the supplier because the original parts listing may not describe the current arrangement.

Step 2: Gather Dimensions and Reference Images

Measure diameter, working length, and overall length, then note the shape and position of grooves, shoulders, holes, and threads. Photograph both ends and the full pin, with a scale included where practical. Mark any measurement as estimated if the pin is damaged or worn. This distinction helps the supplier understand which values are confirmed and which need further verification.

Step 3: Check the Whole Joint

Inspect the bushings and retaining arrangement before finalizing the order. Look for visible scoring, looseness, deformation, or signs that the pin has moved out of position, while following the machine manufacturer’s maintenance procedures. Ask whether the quoted pin is compatible with the existing bushings or whether related parts should be assessed. A replacement decision should address the joint’s condition, not only the removed pin.

Step 4: Confirm the Quotation

Request written confirmation of the application, agreed dimensions, material description, surface or heat-treatment details where applicable, and included components. Ask the supplier to state the minimum order quantity, production or dispatch lead time, packaging, and shipping terms for your specific order. These commercial details can vary by specification, quantity, and destination, so avoid relying on general estimates. Review the drawing or dimensional confirmation before authorizing production when a custom or non-stock specification is involved.

Pricing, MOQ, and Lead-Time Considerations

PC120 bucket pivot pin pricing can depend on dimensions, material, manufacturing requirements, order quantity, and whether associated components are included. A non-standard design or additional documentation request may also affect the quotation process. Minimum order quantity and lead time are supplier- and order-specific; they should be confirmed rather than assumed from the machine model. For planning, provide the target quantity, required delivery location, and preferred schedule with your initial inquiry.

When comparing offers, check that suppliers are quoting the same pin specification and scope of supply. A lower price is not directly comparable if the dimensions, material description, retention features, or included parts differ. Ask how packaging will protect the pin during transport and what inspection or dimensional records can be provided for your order. Keep the confirmed drawing and purchase specification with your maintenance or procurement records.

Supplier Evaluation Checklist

• Can the supplier review the machine serial number, joint location, and available part number?
• Can they confirm the proposed dimensions and relevant end features in writing?
• Are material and process descriptions specific to the quoted product?
• Are MOQ, lead time, packaging, and shipping terms stated for your order?
• Can the supplier explain what measurement or drawing information is still needed?

Zhonghai Jiuchuan supplies excavator bucket pins and related components, including products within the bucket pin and bushing category. We can review the information you provide and discuss a suitable specification for quotation, subject to confirming the application and product details. For a faster review, send the machine model and serial number, joint location, known part number, measured dimensions, photographs, and required quantity. Where exact fitment cannot be verified from the information provided, request confirmation before placing the order.

Conclusion: Confirm Fitment Before Replacement

The reliable way to source a PC120 bucket pivot pin is to verify the specific machine and linkage joint, compare dimensions and end features, and assess the condition of the mating bushings and retainers. Do not order by “PC120” alone or assume a worn pin’s measurements represent its original specification. Gather the serial number, measurements, images, and quantity, then ask the supplier to confirm the proposed part in writing. Contact Zhonghai Jiuchuan with those details to begin a fitment review and quotation for your replacement requirement.

Want more information on PC120 Bucket Pivot Pin? Feel free to contact us.